Search results for "Lead oxide"
showing 7 items of 7 documents
Fabrication and Characterisation of Perovskite Thin Films for Photovoltaic Application
2018
This paper presents an alternative way to obtain perovskite thin films for photovoltaic application. This technique results more competitive, scalable, low-cost, reproducible and is different from other most common methods of fabrication.
Synthesis of Lead Zirconate Antiferroelectric Thin Films by Sol-Gel Processing
2000
A modified methoxyethanol sol-gel process was used for the production of PbZrO3 thin films. The new route uses lead oxide [PbO] instead of lead acetate [Pb(OAc)2]. Through the use of this method it is possible to prepare single-phase perovskite materials with improved properties. Examples are given for PbZrO3 thin layers deposited by the spin coating process on TiO2/Pt/TiO2/SiO2/Si substrates from various sols where lead acetate or lead oxide are used as the starting lead compound. The preferred orientation and the perovskite phase content of the films were studied using X-ray diffraction analysis (XRD). Scanning electron microscopy (SEM) was used for microstructural characterization of the…
Formation of lead by reduction of electrodeposited PbO2: comparison between bulk films and nanowires fabrication
2012
Metallic lead was deposited, both in form of bulk films and nanowire array within pores of anodic alumina membranes, following a new two-step procedure, consisting in anodic electrodeposition of α-PbO2, followed by its reduction to metallic lead. This method allows to overcome drawbacks of the “direct” electrodeposition of lead from aqueous solution, consisting, essentially, in the formation of dendritic deposits. Here, we report the comparison between results obtained in the two cases and discuss the kinetic of oxide reduction both for films and nanowires. Deposit morphology and structure are also discussed. We have found that reduction of α-PbO2 films proceeds always at high speed and uni…
Growth and Electrochemical Performance of Lead and Lead Oxide Nanowire Arrays as Electrodes for Lead-Acid Batteries
2013
n this work, we present the growth and electrochemical performance of nanostructured lead and lead oxide electrodes for lead-acid batteries. The electrodes were obtained by template electrodeposition in polycarbonate membranes, acting as template. Electrochemical tests were conducted at constant current in 5M aqueous solution of sulphuric acid, after assembling nanostructured lead and lead oxide electrodes in a zero-gap configuration using a commercially available separator. The main advantages of these electrodes are the high specific energy and power density, and the wide surface area, about 70 times higher than the geometrical one. These features allowed high discharge rates, up to 20C. …
Recent improvements in PbO2 nanowire electrodes for lead-acid battery
2015
Abstract Lead oxide nanowires are an attractive alternative to conventional pasted electrodes, owing to their high surface area leading to high specific energy batteries. Here, we report the performance of template electrodeposited PbO 2 nanowires used as positive electrodes. Nanostructured electrodes were tested at constant charge/discharge rate from 2 C to 10 C, with a cut-off potential of 1.2 V and discharge depth up to 90% of the gravimetric charge. These new type of electrodes are able to work at very high C-rate without fading, reaching an efficiency of about 90% with a very good cycling stability. In particular, after an initial stabilization, a specific capacity of about 200 mAh g −…
Growth and characterization of PbI2-decorated ZnO nanowires for photodetection applications
2020
Financial support provided by Scientific Research Project for Students and Young Researchers Nr. SJZ/2017/1 realized at the Institute of Solid State Physics, University of Latvia is greatly acknowledged. The authors are grateful to Liga Bikse for XRD measurements.
Indirect Catalytic Spectrophotometric Determination of Metamizol Following Oxidation by Lead Dioxide Immobilized in A Polyester Resin Bed
1996
Abstract A spectrophotometric-indirect procedure for the determination of metamizol is described. The method is based on the reaction of the drug in a solid-phase (lead dioxide immobilized in a polyester resin bed) in acidic media (perchloric acid 0.01 M as carrier). The lead dioxide reactor provides simultaneously an effective oxidation of the drug and a controlled liberation of Pb(II) which acts as catalyst on the reaction pyrogallol red-potassium persulphate; the oxidation of the red pyrogallol results in a less coloured solution. The decreased red colour (negative FIA peaks) is monitored at 520 nm. The calibration graph is linear in the interval 2–16 ppm in metamizol. The relative stand…